
Fire Stop Mortar for Shaft Sealing in Mumbai
Cease Fire & Electrical Services LLP seals service shafts with fire stop mortar in residential towers, commercial buildings and industrial sites in Mumbai. Fire stop mortar forms a solid, load-bearing seal across a shaft opening at each floor, around every pipe and cable that passes through it, so the shaft cannot carry fire and smoke from floor to floor. We build each seal in five steps, from rebar to finished mortar, and issue Form A for the work as a licensed agency.
Why shafts need mortar seals
Electrical, plumbing and drainage shafts run the full height of a building. Unsealed, they act like chimneys: a fire on one floor can send heat and smoke up the shaft to every floor above. Mortar is used for these larger openings because it forms a solid, load-bearing slab, where foam or sealant alone would not be strong enough.
How we seal a shaft
Rebar
We fix 8 mm or 10 mm rebar with crossbars, depending on the shaft size, to give the seal its strength and required thickness.
Wire mesh
A 0.5 mm wire mesh over the rebar forms the base.
Rockwool
Cut and packed around every pipe and cable, it stops the mortar leaking and adds insulation.
Pipe wrap
Fitted around plastic pipes and pipes with combustible insulation, with the number of turns set by the pipe diameter.
Mortar
Mixed by adding mortar to clean water to the right consistency, then pressed into every corner and around every service, removing trapped air, and built up to the required depth.
Smaller gaps left around services are finished with fire-rated foam, sealant or putty cord.
Mortar or sealant?
- Large shaft openings with many services
- Fire stop mortar, built on rebar and mesh
- Openings that must bear load
- Fire stop mortar
- Small gaps around single pipes or cables
- Fire stop sealant or putty cord
- Irregular cavities and cable bunches
- Fire-rated foam
- Plastic pipes in any opening
- Pipe wrap, with mortar or sealant around it
Where mortar seals are used
- Electrical, plumbing and drainage shafts in residential towers
- Service risers in offices, hotels and hospitals
- Cable shafts and cable trenches in factories
- Floor openings left for future services, sealed until they are used
Our process
Free site survey
We measure each shaft opening and list the pipes and cables in it.
Proposal
The seal design for each shaft, with quantities.
Supply and installation
Rebar, mesh, rockwool, pipe wraps and mortar, installed by our own team, floor by floor.
Inspection and handover
Each sealed shaft is checked and recorded, with photos.
Form A
As a licensed agency, we issue Form A for the fire protection work we complete.
Ongoing checks
We can re-inspect under AMC, because new services pushed through a seal later are the most common failure.
Shaft sealing project
Prime Smile, Borivali West (G + 22 residential tower), 2024–25: supply and installation of fire sealant for the service shafts and fire-rated foam, with Form A for the fire doors.
See all projects and case studies.
Why choose Cease Fire
Since 1992
1,500+ projects and the Rashtriya Nirman Ratna Award for Best Government Contractor (2002).
A clear method
The same five steps on every shaft, recorded floor by floor.
Complete range
Mortar, foam, sealants, pipe wraps and putty cord from one team.
Licensed
Maharashtra Fire Services Licensed Agency (MFS/
LA/ ).RF-93/ RD-95
Book a free site survey
Send your shaft sizes, number of floors and photos of the openings. We will inspect the shafts and send a clear proposal.
Frequently asked questions
What is fire stop mortar?
It is a fire-resistant mortar used to seal larger openings, such as service shafts, with a solid layer around the pipes and cables passing through.
Why are service shafts sealed at every floor?
An unsealed shaft acts like a chimney, carrying fire and smoke from floor to floor. Sealing it at each floor keeps the fire in the floor where it started.
Is a fire stop mortar seal load bearing?
Yes. It is built on rebar and wire mesh to give it load-bearing strength. The rebar size depends on the shaft size.
What happens to plastic pipes in a mortar seal?
Plastic pipes and pipes with combustible insulation get a pipe wrap before the mortar is poured. The wrap expands in a fire and closes the hole left by the pipe.
Can new cables be added through a mortar seal later?
Yes, but the seal must be made good afterwards with the right fire-stop product. We can check and repair seals after fit-outs under AMC.
Can mortar seals be added to an existing building?
Yes. We seal existing shafts floor by floor with minimal disruption to residents or occupants.
Do you issue Form A for shaft sealing?
As a Maharashtra Fire Services Licensed Agency, we issue Form A for the fire protection work we complete.
Have you sealed shafts in a high-rise tower?
Yes. We sealed the service shafts at Prime Smile, a G + 22 residential tower in Borivali West, with fire sealant and fire-rated foam, and issued Form A for the fire doors. See the project page.
Question not answered here? Call our team, Monday to Saturday, 9 am to 7 pm.
Call +91 9920676281






