Gloved hands sealing the wall opening around two pipes and a cable tray with red fire-stop sealant

Cease Fire & Electrical Services LLP supplies and installs fire rated board systems in Mumbai to build fire-resistant partitions, duct and shaft enclosures, and linings in residential, commercial and industrial buildings. A fire rated board system is a tested combination of non-combustible boards, framing and joints that holds back fire for a set time, such as one or two hours. We use it where a masonry wall is not practical, for example around ducts and service shafts, or to divide large floors into fire compartments.

Where fire boards are used

Duct and shaft enclosures
Enclose ducts, risers and shafts so fire cannot travel along them
Fire-rated partitions
Divide floors into fire compartments, or separate electrical and plant rooms
Cable route protection
Enclose cable trays that must keep working during a fire
Ceilings and soffits
Form fire-rated ceilings and linings
Structural steel protection
Encase steel so it stays strong for longer in a fire

Types of fire rated board

Calcium silicate board
Non-combustible and tolerant of damp; used for partitions, shaft enclosures, steel protection and ceilings
Fibre cement board
Non-combustible and moisture tolerant; heavier than calcium silicate
Fire-rated gypsum board
Budget option for dry interiors; not suited to damp areas

We recommend the board type from the rating needed, the location and any exposure to damp.

The rating belongs to the whole system

A fire rating is earned by the complete assembly that was tested: the board type and thickness, the number of layers, the framing, fixings, joint treatment and the sealing of any services that pass through. Changing any part can reduce the rating. We build each enclosure or partition to the tested detail for the rating you need, and seal every penetration through it with the right fire-stop product.

Our process

  1. Free site survey

    We look at the ducts, shafts or areas to enclose and the rating required.

  2. Proposal

    Board system, rating, framing and quantities.

  3. Supply and installation

    Boards, framing, fixings, joint treatment and penetration seals, installed by our own team.

  4. Inspection and handover

    Each enclosure or partition is checked and recorded, with photos.

  5. Form A

    As a licensed agency, we issue Form A for the fire protection work we complete.

  6. Ongoing checks

    We can re-inspect under AMC, because later cutting for new services is the most common failure.

Passive fire protection project

Prime Smile, Borivali West (G + 22 residential tower), 2024–25: supply and installation of fire sealant for the service shafts and fire-rated foam, with Form A for the fire doors.

See all projects and case studies.

Why choose Cease Fire

  • Since 1992

    1,500+ projects and the Rashtriya Nirman Ratna Award for Best Government Contractor (2002).

  • Boards and seals together

    Enclosures built and every penetration sealed by one team.

  • Licensed

    Maharashtra Fire Services Licensed Agency (MFS/LA/RF-93/RD-95).

  • MEP know-how

    Our MEP design team understands the ducts and services the boards must enclose.

Book a free site survey

Send your drawings or photos of the ducts, shafts or areas to enclose, and the rating you need. We will visit and send a clear proposal.

Frequently asked questions

What is a fire rated board?

It is a non-combustible board used to build walls, enclosures and linings that resist fire for a set time. The rating comes from the complete tested system, not the board alone.

Where are fire rated boards used?

Around ducts, risers and service shafts, as fire-rated partitions, to protect cable routes, as fire-rated ceilings and to encase structural steel.

What is the difference between calcium silicate and gypsum fire boards?

Calcium silicate board is non-combustible and tolerates damp, so it suits shafts, wet areas and high ratings. Fire-rated gypsum board is a lower-cost option for dry interiors.

How long can a fire board system resist fire?

Tested systems are commonly rated for one, two or even four hours, depending on the board type, thickness, layers and framing.

Can services pass through a fire board partition?

Yes, but every opening must be sealed with a fire-stop product, or the partition loses its rating.

Do you issue Form A for fire board work?

As a Maharashtra Fire Services Licensed Agency, we issue Form A for the fire protection work we complete.

Can fire boards be added to an existing building?

Yes. We survey the ducts, shafts or areas to enclose, build the enclosure to the tested detail and seal every service that passes through it.

Question not answered here? Call our team, Monday to Saturday, 9 am to 7 pm.

Call +91 9920676281