Fire Alarm Zone Module in Mumbai

Two white fire alarm zone modules beside a round smoke detector

Cease Fire & Electrical Services LLP supplies, installs and programs the fire alarm zone module for addressable fire alarm systems in Mumbai, for buildings upgrading an old conventional system and for areas that use conventional detectors. A zone module connects a whole circuit of conventional detectors and call points to an addressable loop, so the addressable panel shows which zone has gone into alarm. We supply zone modules to match your panel and test each connected zone before handover.

How a zone module works

The zone module has its own address on the addressable loop. On the other side it powers and watches a conventional detector circuit, just as a conventional panel would. When any detector or call point on that circuit operates, the module reports the alarm to the addressable panel as one zone. IS 2189:2008 calls this a partially addressable system.

  1. Connects

    A circuit of conventional detectors and call points

    A single switch or contact

  2. Powers the devices

    Yes, it supplies the detector circuit

    No

  3. Panel shows

    The zone that is in alarm

    The single device that has operated

Some zone modules need a separate 24 V supply, depending on the maker.

Where zone modules are used

  • Upgrading a conventional system to an addressable panel while keeping existing detectors and wiring
  • Extending an addressable system into an area already wired for conventional detectors
  • Connecting conventional beam, flame or special detectors to an addressable panel
  • Semi-addressable systems, where each zone rather than each detector is identified

Zone rules to know

A conventional zone behind a zone module still follows the zone rules in IS 2189:2008.

Conventional detectors per zone
No more than 20
Floor area of one zone
No more than 2,000 m²
Search distance to find the fire within a zone
No more than 30 m
Buildings over 300 m² in total
Each zone limited to a single floor
Stairwells, lift wells and shafts
A separate zone

Because the panel only shows the zone, response indicators outside rooms help staff find the detector that has operated.

Supply, installation and servicing

We supply zone modules to match your panel, connect the conventional circuit with its end-of-line device, and program the panel so each zone shows a clear location. Every zone is tested by operating a detector or call point and checking the panel display. Under our AMC, zones are checked during quarterly visits and the annual service.

Engineer testing a wall-mounted fire alarm control panel, with a manual call point and a smoke detector nearby

Why choose Cease Fire

  • Since 1992

    A Maharashtra Fire Services Licensed Agency (MFS/LA/RF-93/RD-95) that designs, installs and maintains fire alarm systems.

  • Proven on addressable work

    Addressable fire alarm systems at 65 Adani Electricity substations in Mumbai.

  • Right part first time

    We confirm panel compatibility and detector compatibility before you order.

Request a quote

Tell us the addressable panel make and model, the number of conventional zones, and the detector make on each zone. We will confirm the modules needed and send a quote.

Frequently asked questions

What is a zone module in a fire alarm system?

It is an addressable module that connects a circuit of conventional detectors and call points to an addressable loop. The panel then shows which zone has gone into alarm.

Can I connect conventional detectors to an addressable panel?

Yes, through a zone module. The panel identifies the zone rather than each detector, so the zone rules in IS 2189 still apply.

How many detectors can a zone module take?

IS 2189 allows no more than 20 conventional detectors in a zone. The maker's limit for the module may be lower, so check the data sheet.

What is the difference between a zone module and a monitor module?

A zone module powers and watches a whole circuit of conventional detectors. A monitor module watches a single switch or contact, such as a flow switch or tamper switch.

Will my existing conventional detectors work with a zone module?

Often, but not always, because conventional detectors and zone modules must be compatible on voltage and alarm current. Share the detector and panel makes and we will confirm.

Does a zone module need its own power supply?

Some do, depending on the maker and the number of detectors. We check this when planning the loop.

Is a zone module system the same as a semi-addressable system?

Yes. IS 2189 calls this a partially addressable system: the panel identifies the zone, not each detector. See our semi-addressable fire alarm system page.

Question not answered here? Call our team, Monday to Saturday, 9 am to 7 pm.

Call +91 9920676281