Deluge Valve for Water Spray and Drencher Systems in Mumbai

A red deluge valve with pressure gauges, trim pipework and a manual release handle

Cease Fire & Electrical Services LLP supplies and installs the deluge valve for water spray (MVWS and HVWS), drencher and foam systems in Mumbai, for transformers, fuel and chemical tanks, conveyors, cable galleries and building openings. A deluge valve holds water back from a network of open nozzles and, when a fire is detected, opens fully so every nozzle in the zone discharges at once. We supply the valve with its release trim and fit it as part of our water spray and drencher work.

How a deluge valve is released

  1. Electric

    A solenoid valve opens on a signal from the detection or release panel and vents the trim

    Most MVWS and HVWS systems with smoke, heat or flame detectors

  2. Wet pilot

    A pilot line of closed sprinklers holds pressure; when one opens, the pressure drop releases the valve

    Outdoor areas where electric detection is not suitable

  3. Dry pilot

    The pilot line holds air instead of water, for areas where water could freeze

    Cold or exposed locations

  4. Manual

    A hand-operated release at the valve or at a remote point

    Always fitted, as a back-up to automatic release

Where deluge valves are used

  • Medium velocity water spray (MVWS): transformers, cable galleries, conveyors and tanks, where the spray cools and controls a fire.
  • High velocity water spray (HVWS): oil-filled transformers and oil tanks, where high-velocity spray puts out an oil fire.
  • Drencher systems: water curtains across openings, escalator voids and building faces.
  • Foam systems: release of the water and foam solution to the protected area.

What to tell us

System
MVWS, HVWS, drencher, foam or other
Size
Valve size from the hydraulic design
Release
Electric, wet pilot, dry pilot, with manual release
Coil voltage
For electric release, as set by the release panel
Approval
UL listed, FM approved or other, as your specification requires

We match the valve, trim and release to your design and specification before supply.

Supply, installation and servicing

We supply deluge valve sets on their own or with the full water spray or drencher system, including the strainers, nozzles and detection. At commissioning we test the release and the discharge pattern. During AMC visits we check the trim pressure and priming, test the release from the panel and by hand, clean the strainers, and check that the isolation valves are open.

Engineer checking a nozzle on the red water spray ring around a power transformer

Why choose Cease Fire

  • Since 1992

    A Maharashtra Fire Services Licensed Agency (MFS/LA/RF-93/RD-95) with 1,500+ projects.

  • Detection and water under one roof

    We install fire alarm and water-based systems, so the release panel, solenoid and deluge valve are tested together.

  • One supplier

    Deluge valves, solenoid valves, strainers, nozzles and installation from one team.

Request a quote

Send your BOQ or drawings with the system type, valve size and release method. We will confirm the specification and quote.

Frequently asked questions

What is a deluge valve?

It is a valve that holds water back from a network of open nozzles or sprinklers. When a fire is detected, it opens fully and water flows to every nozzle in that zone at once.

What is the difference between a deluge valve and an alarm valve?

An alarm valve serves closed sprinkler heads that open one by one in the heat of a fire. A deluge valve serves open nozzles and releases water to all of them together when a detection system triggers it.

How is a deluge valve operated?

Most are released electrically by a solenoid valve on a signal from the detection panel. Others use a wet or dry pilot line of sprinklers, and all have a manual release.

Where are deluge valves used?

In water spray systems for transformers, tanks, conveyors and cable galleries, in drencher systems for openings and building faces, and in foam systems.

How often should a deluge valve be tested?

It should be checked on every maintenance visit and trip-tested as the maintenance schedule requires. We check it during AMC visits and test the release from the panel.

Can you supply UL listed or FM approved deluge valves?

Yes. UL listed and FM approved sprinklers and valves are available. Tell us what your consultant or insurer specifies, and we will share the manufacturer's certificate for the exact model with our quote.

Can the deluge valve release be tested without discharging water?

Test arrangements depend on the valve maker's trim. We test the release from the panel and by hand during commissioning and AMC visits, and follow the maker's test procedure.

Question not answered here? Call our team, Monday to Saturday, 9 am to 7 pm.

Call +91 9920676281